| KASTAŞ NO |
d(f7) dp(h11) |
Db(H11) D(H11) |
B (-0/+0,2) |
n |
| |
| K98-019 |
19,05 |
25,4 |
6,98 |
3
|
| K98-022 |
22,23 |
28,58 |
3,51 |
3
|
| K98-025 |
25,4 |
31,75 |
6,98 |
3
|
| K98-025/1 |
25,4 |
34,93 |
5,28 |
4
|
| K98-025/2 |
25,4 |
34,93 |
8,71 |
4
|
| K98-025/3 |
25,4 |
38,1 |
6,98 |
4,5
|
| K98-031 |
31,75 |
38,1 |
6,98 |
3
|
| K98-031/1 |
31,75 |
41,28 |
8,71 |
4
|
| K98-038 |
38,1 |
47,63 |
8,71 |
4
|
| K98-038/1 |
38,1 |
47,63 |
10,49 |
4
|
| K98-038/2 |
38,1 |
50,8 |
10,49 |
4,5
|
| K98-044 |
44,45 |
53,98 |
10,49 |
4
|
| K98-050 |
50,8 |
60,33 |
10,49 |
4
|
| K98-050/1 |
50,8 |
63,5 |
10,49 |
4,5
|
| K98-057 |
57,15 |
69,85 |
6,98 |
4,5
|
| K98-063 |
63,5 |
76,2 |
10,49 |
4,5
|
| K98-076 |
76,2 |
88,9 |
10,49 |
4,5
|
| K98-088 |
88,9 |
101,6 |
10,49 |
4,5
|
| K98-092 |
92,08 |
101,6 |
10,49 |
4
|
|
 |
|
K98 is a single acting piston - rod seal and designed to have symmetrical lips in order to be used both for rod and pistonapplications. O-ring acts as a spring and provides sealing contact under low pressures and shock pressures.
PRODUCT ADVANTAGES
• Good sealing performance under low pressures and shock pressures
• Superior static and dynamic sealing e ffect
• Easy assembly into closed grooves
• Simple groove design
• Economical sealing solution
APPLICATION
Fork-lift trucks , injection moulding machines , agricultural machinery and standard cylinders.
|
|
|
|
NBR |
70 SHORE A |
NB7001 |
|
PU |
92 SHORE A |
PU9201 |
|
|
OPERATING CONDITIONS |
|
PU |
|
MEDIA |
Mineral oils
(DIN 51524) |
HFA and HFB |
HFC |
|
TEMPERATURE |
-30°C +100°C |
+5°C +50°C |
-30°C +40°C |
|
PRESSURE |
≤400 Bar |
≤400 Bar |
≤400 Bar |
|
SPEED |
≤0.5 m/sn |
≤0.5 m/sn |
≤0.5 m/sn |
|
Note: The above data are maximum values and cannot be used at the same time. |
|
|
|
|
|
|
SURFACE ROUGHNESS |
Ra |
Rmax |
|
Sliding Surface ØD-Ød |
≤0.4 μm |
≤3.2 μm |
|
Groove Base ØDb-Ødp |
≤1.6 μm |
≤10 μm |
|
Groove Flanks B |
≤3.2 μm |
≤16 μm |
|
Note: It is recommended to have 50% to 90% of the working surface material contact area value. |
|
|
|
INSTALLATION
Easily assembled into closed grooves according to the minimum diameter values that are given in the below table. Open grooves or special assembly tools should be used for the values that are outside this table. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation the wiper must be oiled with system oil.
|
|
|
|
MINUMUM DIAMETER VALUES FOR CLOSED TYPE OF GROOVES |
|
(D-d)/2 (mm) |
4 |
5 |
6 |
7.7 |
10 |
12.5 |
15 |
|
dmin (mm) |
25 |
30 |
40 |
50 |
80 |
100 |
105 |
|
NOTES
The permissible sealing gap values of K98 piston -rod seal is given in the below table.
|
|
|
t=(D-d)/2 |
150 Bar |
250 Bar |
400 Bar |
|
t≤5 |
0.30 |
0.20 |
0.15 |
|
t>5 |
0.35 |
0.25 |
0.20 |
Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.
|
|
